GASKETS FRONT AXLE (FULL SET)
Gasket kit for steering knuckle with parafin impregnated felt
Front Axle Gaskets – Complete Set
Complete gasket set for front axle overhaul
Complete gasket set for full front axle overhaul. This comprehensive set contains all required gaskets and seals for a thorough front axle rebuild: pinion seals, wheel hub gaskets, axle shaft seals, steering knuckle gaskets and differential cover gasket.
|
Application Front axle overhaul |
Type Complete gasket set |
|
Vehicle See categories |
Set contents All front axle gaskets and seals |
Features
- Complete set for front axle overhaul
- Pinion seals and gaskets
- Wheel hub seals (left + right)
- Axle shaft seals (inner)
- Steering knuckle seal sets
- Differential cover gasket
★ Professional gasket set for complete front axle overhaul – everything needed for proper sealing and reliable operation after rebuild.
Application
This gasket set is intended for jeeps listed in the categories: MB, CJ-2A, CJ-3A, M38, M38A1 and CJ-3B. Verify that the set is suitable for your specific front axle type (Dana 25 or Dana 27) and year of manufacture before ordering.
Installation notes
Installation requires front axle disassembly. Use correct shims and adjust bearing preload properly. Replace all seals and gaskets during overhaul – reusing old gaskets leads to leaks. Follow factory procedure for correct installation of pinion bearings and differential bearings.
Compatibility
Suitable for various Dana 25 and Dana 27 front axles, depending on vehicle model. MB and GPW use Dana 25 (1941-1945), CJ-2A and CJ-3A also Dana 25 (1945-1953), M38 has Dana 25 (1950-1952), whilst M38A1 and CJ-3B may have Dana 25 or Dana 27 depending on year of manufacture. Check which front axle is fitted in your vehicle before ordering.
Historical context
The Dana/Spicer front axles were the backbone of the WWII jeep and later civilian variants. Complete gasket sets were standard for depot-level maintenance, where axles were completely stripped and overhauled.
This description was generated automatically. Unsure about fitment? Contact us at info@willys.be.
⚠ Spotted an error in this description? Report it to info@willys.be
This part is intended for the restoration of historic military vehicles. Fitting, aligning, deburring or reworking is part of that work and is inherent to the nature of these goods. Dimensional variation also exists between original vehicles.
Installation requires technical knowledge of the vehicle. Unsure whether this part suits your version? Ask us before purchase at info@willys.be.
ALL_CATEGORIES : GROUP 10 - FRONT AXLE CJ2A, GROUP 10 - FRONT AXLE CJ3A, GROUP 10 - FRONT AXLE - M38, GROUP 10 - FRONT AXLE CJ3B
This part fits:
| Model | Years |
|---|---|
| Military jeeps | |
| Willys MB (early) | 1941, 1942 |
| Willys MB | 1942, 1943, 1944, 1945 |
| Ford GPW (early) | 1942 |
| Ford GPW | 1942, 1943, 1944, 1945 |
| Hotchkiss M201 | 1956, 1957, 1958, 1959, 1960, 1961, 1962, 1963, 1964, 1965, 1966 |
| Willys M38 | 1950, 1951, 1952 |
| Willys M38A1 | 1952, 1953, 1954, 1955, 1956, 1957, 1958, 1959, 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1969, 1970, 1971 |
| CJ series | |
| Jeep CJ-2A | 1945, 1946, 1947, 1948, 1949 |
| Jeep CJ-3A | 1949, 1950, 1951, 1952, 1953 |
| Jeep CJ-3B | 1953, 1954, 1955, 1956, 1957, 1958, 1959, 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968 |
| Jeep CJ-5 | 1955, 1956, 1957, 1958, 1959, 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1969, 1970, 1971, 1972, 1973, 1974, 1975, 1976, 1977, 1978, 1979, 1980, 1981, 1982, 1983 |
📐 Diagrams & technical drawings
From the original Technical Manual CJ2A_PL_1949 — Parts List — only for Willys CJ-2A / CJ-3A (1949)
From the original Technical Manual TM 9-1803B — Ordnance Maintenance — Power Train, Body & Frame — only for Willys MB / Ford GPW (¼-ton 4×4)
