DIFFERENTIAL SPIDER GEAR SET DANNA 44
Differential Spider Gear Set Dana 44
Complete set for rear axle
Complete spider gear set for the Dana 44 rear axle as fitted to military jeeps and early CJ models. This set contains all necessary parts for a complete differential overhaul: spider gears, side gears, bevelled and flat washers, and cross pin.
|
Application Dana 44 rear axle |
Vehicles CJ-2A, M38, M38A1, CJ-3B |
|
Type Open differential |
Kit contents Spider gears, side gears, washers, cross pin |
Features
- Complete set with all necessary parts
- For Dana 44 rear axle with open differential
- Contains spider gears and side gears
- Includes bevelled and flat thrust washers
- With cross shaft pin
★ Quality parts for correct overhaul of your Dana 44 differential. Suitable for early military and civilian jeeps fitted with Dana 44 rear axle.
Application
Fits vehicles with Dana 44 rear axle: CJ-2A (late versions with Dana 44), M38 (1950-1952), M38A1 (1952-1971), and CJ-3B (1953-1964). Note: check the spline count of your axle shafts (10, 19 or 30 spline) beforehand to order the correct set.
Installation notes
Overhauling a differential requires specialist knowledge and specific tools. Components must be assembled within precise tolerances. Check the wear of all components and replace bearings and seals if necessary. Consult the technical manual for correct assembly sequence and adjustments.
Compatibility
Suitable for Dana 44 rear axle with open differential. NOT suitable for limited-slip or Trac-Lok differentials. The Dana 44 was fitted from 1950 onwards to various military and civilian jeeps, but came in different versions with 10, 19 or 30 spline axle shafts. Check the spline count before ordering.
Historical context
The Dana 44 rear axle became standard from 1950 on the military M38 and later on the M38A1. This robust semi-floating axle with tapered axle shafts was the standard rear axle on many Willys jeeps up to the 1/2-ton class until the late 1960s.
This description was generated automatically. Unsure about fitment? Contact us at info@willys.be.
⚠ Spotted an error in this description? Report it to info@willys.be
This part is intended for the restoration of historic military vehicles. Fitting, aligning, deburring or reworking is part of that work and is inherent to the nature of these goods. Dimensional variation also exists between original vehicles.
Installation requires technical knowledge of the vehicle. Unsure whether this part suits your version? Ask us before purchase at info@willys.be.
ALL_CATEGORIES : GROUP 11 REAR AXLE DANA 44, GROUP 11 - REAR AXLE CJ2A, GROUP 11 REAR AXLE DANA 44 3B, GROUP 11 REAR AXLE DANA 44 CJ3B
This part fits:
| Model | Years |
|---|---|
| Military jeeps | |
| Willys M38 | 1950, 1951, 1952 |
| Willys M38A1 | 1952, 1953, 1954, 1955, 1956, 1957, 1958, 1959, 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1969, 1970, 1971 |
| CJ series | |
| Jeep CJ-2A | 1945, 1946, 1947, 1948, 1949 |
| Jeep CJ-3A | 1949, 1950, 1951, 1952, 1953 |
| Jeep CJ-3B | 1953, 1954, 1955, 1956, 1957, 1958, 1959, 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968 |
| Jeep CJ-5 | 1955, 1956, 1957, 1958, 1959, 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1969, 1970, 1971, 1972, 1973, 1974, 1975, 1976, 1977, 1978, 1979, 1980, 1981, 1982, 1983 |
📐 Diagrams & technical drawings
From the original Technical Manual CJ2A_PL_1949 — Parts List — only for Willys CJ-2A / CJ-3A (1949)
