TUBE BRAKE REAR AXLE LEFT DRIVER SITE
WOA5225
Brake line rear axle left driver's side
Pre-bent steel brake line
Pre-bent steel brake line for the rear axle left (driver's side). This brake line connects the master cylinder to the left wheel cylinder at the rear and is essential for a reliable braking system.
|
Material Steel |
Position Rear axle left |
|
Application CJ-2A, CJ-3A, M38, CJ-3B |
Type Pre-bent line with fittings |
Features
- Pre-bent steel brake line for exact fit
- Suitable for rear axle left (driver's side)
- Supplied with flared connections
- Replaces corroded or damaged original lines
- Essential component for brake safety
★ Precisely pre-bent brake line that can be fitted directly without on-site adjustments.
Application
Fits Willys CJ-2A (1945-1949), CJ-3A (1948-1953), M38 (1950-1952) and CJ-3B (1953-1968) with 9" brake system. Note: for CJ-2A with Dana 41 rear axle and later models with Dana 44 rear axle. Always verify the original configuration of your vehicle.
Installation notes
Remove the old brake line and flush the brake system thoroughly. Fit the new line from wheel cylinder to T-piece on the axle. Use new copper sealing washers at the connections. Bleed the complete brake system after fitting as prescribed.
Compatibility
Suitable for left (driver's) side rear axle. Not interchangeable with right side. Check the routing and length of the original line before fitting. When converting to 11" brakes or disc brakes, different lines may be required.
Historical context
The original brake lines on CJ-series vehicles were routed along the rear axle with metal clips. Due to exposure to moisture, salt and off-road use, these lines often corrode, which compromises brake safety.
This description was generated automatically. Unsure about fitment? Contact us at info@willys.be.
⚠ Spotted an error in this description? Report it to info@willys.be
This part is intended for the restoration of historic military vehicles. Fitting, aligning, deburring or reworking is part of that work and is inherent to the nature of these goods. Dimensional variation also exists between original vehicles.
Installation requires technical knowledge of the vehicle. Unsure whether this part suits your version? Ask us before purchase at info@willys.be.
ALL_CATEGORIES : BRAKES TUBES CJ2A, BRAKES TUBES CJ3A, BRAKES TUBES M38, BRAKES TUBES CJ3B
This part fits:
| Model | Years |
|---|---|
| Military jeeps | |
| Willys MB (early) | 1941, 1942 |
| Willys MB | 1942, 1943, 1944, 1945 |
| Ford GPW (early) | 1942 |
| Ford GPW | 1942, 1943, 1944, 1945 |
| Hotchkiss M201 (early) | 1956, 1957, 1958, 1959 |
| Hotchkiss M201 | 1956, 1957, 1958, 1959, 1960, 1961, 1962, 1963, 1964, 1965, 1966 |
| Willys M38 | 1950, 1951, 1952 |
| Willys M38A1 | 1952, 1953, 1954, 1955, 1956, 1957, 1958, 1959, 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1969, 1970, 1971 |
| CJ series | |
| Jeep CJ-2A | 1945, 1946, 1947, 1948, 1949 |
| Jeep CJ-3A | 1949, 1950, 1951, 1952, 1953 |
| Jeep CJ-3B | 1953, 1954, 1955, 1956, 1957, 1958, 1959, 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968 |
| Jeep CJ-5 | 1955, 1956, 1957, 1958, 1959, 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1969, 1970, 1971, 1972, 1973, 1974, 1975, 1976, 1977, 1978, 1979, 1980, 1981, 1982, 1983 |
📐 Diagrams & technical drawings
From the original Technical Manual CJ2A_PL_1949 — Parts List — only for Willys CJ-2A / CJ-3A (1949)
