YOKE PROPELLER SHAFT JEEP
Propeller shaft slip yoke
For front and rear propeller shaft
Slip yoke for the propeller shaft, suitable for both the front and rear drive shaft. This component forms the telescopic part of the propeller shaft that slides into the transfer case or differential. Supplied complete with dust boot and seal.
|
Material Steel |
Application Front and rear propeller shaft |
|
Version With dust boot and seal |
Required quantity 2 pieces per vehicle (front + rear) |
Features
- Slip yoke with internal spline for telescopic operation
- Complete with dust boot and grease seal
- Pre-assembled and ready to fit
- Fitted with grease nipple for maintenance
- Suitable for front and rear propeller shaft
★ Ideal when only the yoke needs replacing without having to replace the entire propeller shaft. A cost-effective solution for driveline repair.
Application
This component fits the categories listed: CJ-2A (1946-1949), CJ-3A (1949-1953), CJ-3B (1953-1964) and M38 (1950-1952). Two slip yokes are required per vehicle: one for the front and one for the rear propeller shaft.
Installation notes
Ensure the yoke is installed in the correct orientation — mark the original position before removal. The grease nipple must remain accessible after fitting for periodic greasing. Check that the dust boot is properly secured to prevent ingress of dirt and moisture loss.
Compatibility
Please note: this concerns the slip yoke (sliding yoke / slip yoke) for the propeller shaft itself, not the fixed yokes of the transfer case (A1106) or differential (A1445). Check the part number on your original component if in doubt.
Historical context
The telescopic slip yoke has been part of the four-wheel drive jeep driveline since the Second World War and compensates for longitudinal movement of the propeller shaft during suspension travel.
This description was generated automatically. Unsure about fitment? Contact us at info@willys.be.
⚠ Spotted an error in this description? Report it to info@willys.be
This part is intended for the restoration of historic military vehicles. Fitting, aligning, deburring or reworking is part of that work and is inherent to the nature of these goods. Dimensional variation also exists between original vehicles.
Installation requires technical knowledge of the vehicle. Unsure whether this part suits your version? Ask us before purchase at info@willys.be.
ALL_CATEGORIES : GROUP 09 - PROPELLER SHAFT CJ2A, GROUP 09 - PROPELLER SHAFT CJ3A, GROUP 09 - PROPELLER SHAFT M38, GROUP 09 - PROPELLER SHAFT CJ3B
This part fits:
| Model | Years |
|---|---|
| Military jeeps | |
| Willys MB (early) | 1941, 1942 |
| Willys MB | 1942, 1943, 1944, 1945 |
| Ford GPW | 1942, 1943, 1944, 1945 |
| Hotchkiss M201 | 1956, 1957, 1958, 1959, 1960, 1961, 1962, 1963, 1964, 1965, 1966 |
| Willys M38 | 1950, 1951, 1952 |
| CJ series | |
| Jeep CJ-2A | 1945, 1946, 1947, 1948, 1949 |
| Jeep CJ-3A | 1949, 1950, 1951, 1952, 1953 |
| Jeep CJ-3B | 1953, 1954, 1955, 1956, 1957, 1958, 1959, 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968 |
📐 Diagrams & technical drawings
From the original Technical Manual CJ2A_PL_1949 — Parts List — only for Willys CJ-2A / CJ-3A (1949)
